Film Projectors Bell & Howell

All Devices | Digitize by Yourself | Electronics | Film Camera - analogue | Film Projector Parts | Film Projectors | Film, slide and photo scanners | Films | Formats | Information | Lamps | Miscellaneous | Photo Enlargers | Photograpy | Rewinders | Slide Projector Parts | Slide Projectors | Splicers | Video Equipment | Video Parts | Viewer Parts | Viewers

 

Bell & Howell, 489 Filmosound 8

Show device details

Bell & Howell 489 Filmosound 8

marketed in 1971-72
design: 489Z
super 8 mm film

LENS: Zoom type, 9-element design, 17mm to 30mm range,
f/1.6.

LAMP 8-volt 50-watt internal reflector tungsten-halogen type.
pre-heated when unit is plugged in for extended life.

PROJECTION SPEED: 18 to 24 frames per second, continuously
adjustable.

SOUND/ PICTURE SEPARATION: Sound is 18 frames ahead of
the picture, conforms to ASA standards.

Recording Input: Microphone input 3 to 10 mv,
impedance 4K ohms: audio input .3 mv to 2 volts, impedance 4K
ohms to 1 megohm. Same socket used for either input.
MIXll~G CONTROL: For combining voice (2nd recording) with
music background (1st recording). or for fading sound in or out.
AUTOMATIC RECORDING LEVEL: Compensates recording level
fluctuations up to 30 db. Response time 150 mill iseconds.
AMPLIFIER: Combined recording and playback ampl ifier with
integrated circuits: 2-watt push-pull output; monitoring provision
during recording.

FREQUENCY RANGE OF SOUND STRIPE: 80-8000 Hz at 18
fps, 75-10000 Hz at 24 fps.

SPEAKER: Bu1lt-1n 4" round speaker. 4 to 8 ohms impedance,
2 to 6 watts capacity range.

LINE OUTPUT: Provision for addition of external amplifier system.
Nominal value-Ra 100K ohms, Ua 450 mv.

SIGNAL/NOISE RATIO: 40 db.
SPEED FLUCTUATION: Less than ±4%, controlled by ballbearing
flywheel.
FREQUENCY FLUCTUATION: Less than ±.15%.
FLUTIER: Less than ±.2%.
SOUND HEAD: Replaceable recording / playback head, 5 micron
gap, average service life 200 sound operating hours.

ERASING HEAD: Has high-frequency premagnetization and
erasing at 50,000 Hz.

VOLTAGE SELECTION: Pre-set at t 17 volts. 60 Hz; can be
changed to 240, 230, 220. 200. 160, 127. 110, or 100 volts at
either 50 Hz or 60 Hz.

Weight: 7610 gram
Size: 32 x 18 x 23 cm
made in Austria by Eumig

This projector is similar to the Eumig Mark S 705

Bell & Howell 489 Filmosound 8

marketed in 1971-72
design: 489Z
super 8 mm film

LENS: Zoom type, 9-element design, 17mm to 30mm range,
f/1.6.

LAMP 8-volt 50-watt internal reflector tungsten-halogen type.
pre-heated when unit is plugged in for extended life.

PROJECTION SPEED: 18 to 24 frames per second, continuously
adjustable.
Meer lezen

Relevant products

  LS-0017
  LS-0144
  LS-0155
  LS-0317
  LS-0357
  SP-0005
Original price was: € 379,00.Current price is: € 359,00.
  RW-0062
  DV-0038

Images

Click on an image to enlarge.

  • Bell & Howell 489 Filmosound 8

;

Frequently asked questions

Tips for repairing a film projector and addresses for repair shops

Tips for repairing a film projector and addresses for repair shops

Link to this page: https://van-eck.net/hrf_faq/kan-ik-zelf-mijn-filmprojector-of-diaprojector-repareren/

Can I repair my film projector or slide projector myself?

It depends very much on your own dexterity. If a projector has been idle for a long time, a repair often begins with:
  • removing old fat
  • apply new lubrication
  • replacing strings
  • lamp replacement
If you are somewhat handy, the above problems can often be solved yourself, with the right tools and parts. This solves the problems in many cases. However, not always. Other common problems:
  • the lamp base is defective
  • gears are cracked and need to be replaced
  • electronic components are defective. You can think of capacitors, diodes, resistors, ICs.
  • the gripper adjustment is no longer correct
  • the framework setting must be adjusted
  • the cam / cam follower needs to be replaced.
For these problems it is often necessary to call in a professional. For parts to order, see our parts finder . Tools for repairing film projectors and slide projectors Maintenance products for cleaning and lubricating your film projector or slide projector  

Addresses for maintenance and repair film and video equipment

Netherlands:
  • Corona Imaging – Almere, https://www.coronabeeldtechniek.nl/projector-reparatie/ +31 (0)36 546 9565 service@coronabeeldtechniek.nl (all)
  • Erik Snel – Drachten, E-mail: menerik.snel@gmail.com (specialist Eumig and mechanical problems)
  • Digital Super8 – Venray, E-mail: digitalsuper8@gmail.com – repair of Elmo GS1200 and Bauer super8 projectors. On the basis of intake is determined whether repair is possible or is possibly referred
  • Electro Service Midden Brabant (Udenhout – North Brabant) : https://www.esmb.nl: Video, Camcorders, Tape recorders
  • Technivision www.technivision.nl Eindhoven: image and sound equipment repairs
Belgium:
  • Steve De Wachter, E-mail: kipropsandcollectables@gmail.com, Korenbloemstraat 24, 9150 Kruibeke, East Flanders, Belgium.
Australia:
  • Joel Bleakley – Melbourne area – joelbleakley@gmail.com
France: Italy:
  • Ciao da Francesco E-mail: prospero1977@hotmail.com (16mm, 35mm, 70mm film equipment)
United Kingdom:
  • John White Projector Repair: http://www.the8mmshedshop.co.uk/
United States:
  • John Capazzo – New Jersey USA – Phone: 973 923 0636 – Repairs Elmo, Eumig ans Sankyo
  • Bill Phillips – 16mmprojector repair https://16mmprojectorrepair.com/ pcav@optonline.net – Eiki, B&H, Hokushin, Long Island, NY.
  • http://www.rcsclassic16mm.com/ – Flin, MI, USA – B&H, EIKI, Elmo, Ringmaster
  • Paul Fortea (Chicage area) : Offering worm gear replacement and rebuilds on all Bell and Howell 1500-2500 series autoload or manual load projectors,no slot loads,prices will be very…. basic rebuilds include new aircraft aluminum gear,new main drive motor belt,timing adjustment,cleaning old and new lubrication..any other parts would need to be replaced,any soundboard issues I do not work on,either the board needs to be replaced or you will need to find an electronic person to diagnose,shipping both ways is your cost,if you live in the midwest dropoff is accepted…turnaround times varies,but usually a week or less..please email paulfortea@aol.com me if you have interest
Canada: